indstair1Safe Floors industrial anti-slip products are manufactured entirely by hand in a unique one step manufacturing process then trimmed and cut to size. By incorporating all of the separate elements of the finished product into one seamless fiberglass composite material we are able to build the strongest and most durable product available on today’s market. The general term for the way we make our product is Fibre Reinforced Plastic or FRP for short, or more commonly called fiberglass.

FRP doesn’t dent, corrode, rot, delaminate, support bacteria and has a high strength to weight ratio being several times higher than steel on a weight to weight basis. indstair2It demonstrates a very high resistance to UV and other environmental conditions is highly resistant to chemical attack and has an indefinite lifespan. The particular base resin used by Safety Step also features extremely good fire retardant and low smoke emission characteristics. 

Almost all other stair nosing and floor plate manufacturers adopt a layering or bonding method where an anti-slip coating is bonded to a pre-formed base such as steel or pultruded material. This method invariable sets up a weak point where the two dissimilar components, the top coating and the base material, meet . This weak point will be further strained by stress set up within the product through movement associated with normal use or t hrough thermal expansion and contraction. indstair3Such a bonding method also has a low tolerance to impact and typically the top coatin will peel away from damaged or impacted areas. 

The products you receive from Safety Step are constructed from a base mix of fire retardant polyester resins interspersed with layers of immensely strong interwoven glass fibre. The colour pigmentation is floated right through the full thickness of the material so that it is impossible to wear the colour off and become unsightly.

The fused alumina anti-slip grain is then forced under pressure into the base mix while it is still wet, followed by a final resin layer laid over the top of it all. This entire composite mix is then cured at optimum temperatures until fully hard.

No layering, no bonding, no weak spots, just one immensely strong composite whole.

With safety Step products the anti-slip grit cannot be knocked out as happens with over-coating methods, no peel back or chipping can occur around localised damage points, the colour cannot be worn off, flexing and movement will have no effect on them and with the FRP material, there is a 100% guarantee that it cannot rust or corrode.

You simply get the toughest, most durable and longest lasting nosing’s available anywhere in the world.


AVAILABLE COLOURS

INDUSTRIAL:STAIR NOSINGS

Industrial Stair Nosing’s are available in two ‘in stock’ or standard colours, SAFETY YELLOW and BLACK

indstair4

Additionally four other colours are available ‘on request’, RED, WHITE, GREEN and BLUE.

indstair6

Glow in the dark stair nosing’s are available that look off white to green in daylight and glow bright green/yellow in darkness.


 

indstair8

INDUSTRIAL: STAIR NOSINGS

Safety Step produce a range of standard or ‘in stock’ length Industrial Nosing’s from 450mm (18”) to 1200mm (48”) to accommodate almost all widths of steps. Other sizes up to a length of 3.6m (11’8”) can be ordered. STAIR NOSINGS are offered in two series of tread depth 75mm and 150mm depth. Return: The return on all Industrial Stair Nosing’s is standard at 25mm. This nosing return has three key functions

a) It adds substantial rigidity to the stair nosing.

b) When ascending the steps the drop offers good step edge definition.

c) It allows the anti-slip texture to extend right to the very edge of the stair nosing offering maximum grip.

indstair10indstair11

INDUSTRIAL WALKWAY COVERS

PRODUCT SCHEDULE

WALKWAY COVERS are offered in flat sheets in varying standard sizes measured in two dimensions, length and width.

The thickness of WALKWAY COVERS will vary dependent upon the grit texture specified, the coarser the grit - the thicker the cover, and will range between 4mm and 7mm

indstair12indstair13

LADDER RUNG COVERS

PRODUCT SCHEDULE

LADDER RUNG COVERS are available in SQUARE or "U" section in a series of standard lengths and widths.

indstair14indstair15

Client Testimonials

David Marchant

Ourimbah - NSW

"Once we had decided to get the floors re done, knowing who to get was a bit of a challenge, but we were then recommended to your company and I must say I'm so glad that you were recommended! Very good job, everyone is really impressed. Keep up the good work Rob!"
 

John Winston

Somersby - NSW

"Hi Rob, just wanted to say thanks for an excellent job. I was really impressed with the way the whole thing went. It's a real good feeling knowing that this workplace is safer now I must say! I would have no hesitation in recommending your company Rob, very professional and courteous too."
 
 

NEED TO KNOW MORE INFORMATION?

Book In Your Obligation Free Consultation Here

We can provide you with the best quality product, guaranteed!